PIC Programming using ICSP and ICPROG

IC-Prog is a free windows program that you can use for PIC Programming. It interfaces using either the serial or parallel port on a PC. You can download IC-Prog here. The following devices are currently supported IC-Prog software.

Microchip PIC devices:  12C50812C508A12C50912C509A12CE51812CE51912C67112C67212CE67312CE67412F62912F67516C43316C5416C5616C5816C6116C62A16C62B16C6316C63A16C64A16C65A16C65B16C6616C6716C7116C7216C72A16C73A16C73B16C74A16C74B16C7616C7716F7316F7416F7616F7716C8416F8316F8416F84A16F8816C50516C62016C620A16C62116C621A16C62216C622A16CE62316CE62416CE62516F62716F628 Pull PGM to GND!16F628A16F648A Pull PGM to GND!16F63016F67616C71016C71116C71216C71516C71616C71716C74516C76516C77016C77116C77316C77416C78116C78216F81816F81916F87016F87116F87216F87316F87416F87616F877 Pull PGM to GND!16F873A16F874A16F876A16F877A Pull PGM to GND!16C92316C92418F24218F24818F25218F25818F44218F44818F45218F458 Pull PGM to GND!18F132018F233018F432018F662018F672018F862018F8720 Pull PGM to GND!
Spi Microcontrollers:  90S120090S231390S232390S233390S234390S441490S443390S443490S851590S853589S5389S8252
Flash Microcontrollers:  89C105189C205189C4051
Philips Serial Microcontrollers:  P87LPC762P87LPC764P87LPC767P87LPC768
I2C eeproms:  24C01A24C0224C0424C0824C1624C3224C6424C65AT24C128AT24C256AT24C512 (Atmel)M24C128M24C25624C515 (Microchip)PCF8572 or 8572 = 24C01PCF8582 or 8582 = 24C02PCF8592 or 8592 = 24C04SDA2506SDA2516SDA2526SDA2546SDA2586SDA3506SDA3516SDA35264C016 == 24C01GRS-003 == 24C02GRN-004 == 24C04GRN-008 == 24C04GRX-006 == 24C04GRX-007 == 24C04KKZ06F == 24C01BAW658049 == 24C02BAW57452 == 24C02M8571 == 24C02X24C0124LC21 = 24C01 ( Pin7 (VCLK) must be connected to VCC !!)
4-Wire eeproms:  59C1159C2259C13
Spi eeproms:   25010250202404025080251602532025640
Microwire eeproms:  93C0693C4693C5793C5693C6693C7693C8693C13 = 93C0693C14 = 93C46GRO-001 = 93C46GRN-001 = 93C46GRN-002 = 93C46KKZ01 = 93C466005L = 93C06B22AN = 93C06P8911 = 93C06CAT35C102 = 93C56CAT35C104 = 93C66CAT35C108 = 93C76
Modern Serial eeproms:  AK6420AK6440 AK6480 Still experimental!BR9010BR9020BR9040BR9080BR9016BR9021CXK1011CXK1012CXK1013PDG011TC89101TC89102NS7002NS77007M6M80011M6M80021M6M80041ER1400 (Use special ER1400 Programmer!)M58657 == ER1400
IM-Bus eeproms:  NVM3060MDA2061MDA2062
Scenix/Ubicom devices : SX18SX20SX28SX48SX52


Setting up the IC-Prog environment
When we first start IC-Prog this is the screen we see for selecting the hardware for the PIC programmer; I have selected JDM programmer - a serial port programmer, Windows API - interface and leave rest of the settings same.

Press OK to continue. After this the main program screen is displayed.

How to select a device to program:

Device can be selected in two ways. Firstly, we can select our device (in my case it is 16f877a) from combobox located at top right side of the IC-Prog software window.

Secondly, goto to software menu and select Settings->Device->Microchip PIC->More->More->PIC 16f877a.

Now goto File->Open and select hex file to be uploaded (burned) in PIC 16f877a microcontroller. When opened file get loaded in IC-Prog buffer following action can be taken :

Program Device

The program device button does just that it programs the contents loaded from the hex file (in IC-Prog memory) into the program memory of the PIC micro. If there is any EEPROM in the chip then it programs this as well. Finally it programs the configuration word

Read Device

The read device button reads back the entire contents of the chip into the currently selected buffer (shown at the bottom of the ICPROG window). So you can save the hex file or compare it to the contents of another buffer.

Verify Device

The verify device button reads back the entire contents of the chip ensuring that it matches the hex file. Verification may automatically happen at the end.Once you get used to IC-Prog and your hardware works reliably you may only want to do a verify if something does not work otherwise it takes more time up.

Note: Depending on settings in menu (Settings->Options->Programming)

Erase Device

The next PIC programming action is to erase the device by hitting the erase device button. It sends a command to the PIC which erases the whole device including protection bits. So this command quickly erases the chip.

Note: You don't have to use the erase button as the program button will overwrite the chip contents anyway. It is sometimes useful if you want to convince yourself that the program is actually programmed into the device correctly.

Which are ICSP pins of microcontroller
As we know ICSP pins are used to upload hex file in microcontroller. Here are ICSP pins of some PIC microcontroller.

16f84

16f877

16f628

18f452

18f2550

Some Useful Videos

Watch following videos to setting up the JDM Programmer hardware settings in IC-Prog software and uploading hex file in microcontroller (in my case it is 16f877a).

IC-Prog Settings

Uploading hex file